Editing Talk:The Piles Centre (section)

== Another Issue ==

I found an issue about one of the elevator shafts (Shaft 9), and I can't fix it although all code of the shaft 9 are correct.<br>This doesn't apply to the 2nd floor. Very strange! 

[[File:Imageaa.jpg|200px]]

Scripting code:<br>
<pre>
<nowiki>#</nowiki>Shaft 9 (Mueller Elevators)

AddShaft 9, 27, 52, 2, 4

Set z1 = -13.8
Set x1 = -6.125 + 0.33 - 0.5
Set z2 = 5
Set x2 = 6.125 + 0.3

ShaftCut 9, %x1%, %z1%, %x2%, %z2%, 0, 5

<Floors 2 to 3>
	FloorOrientation = top
	DrawWalls = false, true, false, false, false, false
	if[%floor% = 2] AddShaftFloor 9, Shaft9Base, Brick, 0.5, %x1%, %z1%, %x2%, %z2%, 0, 0, false, false, 0, 0
	DrawWalls = true, true, false, false, false, false
	if[%floor% = 3] AddShaftFloor 9, Shaft9Top, Brick, 0.5, %x1%, %z1%, %x2%, %z2%, %fullheight%, %fullheight%, false, false, 0, 0
	DrawWalls = true, true, false, false, false, false
	WallOrientation = left
	AddShaftWall 9, Shaft9Left, Brick, 0.33, %x1%, %z1%, %x1%, %z2%, %fullheight%, %fullheight%, 0, 0, 0, 0
	AddShaftWall 9, Shaft9Front, Brick, 0.33, %x1%, %z1%, %x2%, %z1%, %fullheight%, %fullheight%, 0, 0, 0, 0
	WallOrientation = right
	AddShaftWall 9, Shaft9Right, Brick, 0.33, %x2%, %z1%, %x2%, %z2%, %fullheight%, %fullheight%, 0, 0, 0, 0
	AddShaftWall 9, Shaft9Back, Brick, 0.33, %x1%, %z2%, %x2%, %z2%, %fullheight%, %fullheight%, 0, 0, 0, 0

	Set x1 = 20.64
	Set z1 = 38.14
	Set x2 = 33.71
	Set z2 = 57.10

	WallOrientation = right
	DrawWalls = true, false, false, false, false, false
	AddWall Shaft9LeftE, MuellerWall, 0.33, %x1%, %z1%, %x1%, %z2%, %fullheight%, %fullheight%, 0, 0, 0, 0, False
	AddWall Shaft9FrontE, MuellerWall, 0.33, %x1%, %z1%, %x2%, %z1%, %fullheight%, %fullheight%, 0, 0, 0, 0, False
	WallOrientation = left
	DrawWalls = false, true, false, false, false, false
	AddWall Shaft9RightE, MuellerWall, 0.33, %x2%, %z1%, %x2%, %z2%, %fullheight%, %fullheight%, 0, 0, 0, 0, False
	AddWall Shaft9BackE, MuellerWall, 0.33, %x1%, %z2%, %x2%, %z2%, %fullheight%, %fullheight%, 0, 0, 0, 0, False


	DrawWalls = true, true, true, true, false, false
<EndFloors>

<nowiki>#</nowiki>reset drawwalls
DrawWalls = true, true, false, false, false, false
</pre> [[User:Lighthouse Friesland|Lighthouse Friesland]] ([[User talk:Lighthouse Friesland|talk]]) 05:19, 1 July 2024 (CDT)

:Issue has finally been fixed. I forgot to put 
:<code>Set z1 = -13.8</code>
:<code>Set x1 = -6.125 + 0.33 - 0.5</code>
:<code>Set z2 = 5</code>
:<code>Set x2 = 6.125 + 0.3</code> again inside a floor range command.
:s [[User:Lighthouse Friesland|Lighthouse Friesland]] ([[User talk:Lighthouse Friesland|talk]]) 11:22, 4 July 2024 (CDT)